 |
 |
 |
|
Crown's XLS Series amplifiers define the standard for group fitness sound systems with unmatched performance, technology and affordability. Its flexibility includes multiple input connectors so you can plug in anything and play anywhere, along with several system setup configurations. The integrated crossovers and switch-mode power supply produce superior sound, and Peakx™ limiters protect your speakers. Weighing less than 12 pounds, compared to 40 pounds for its competitors, it's much easier to set up and makes wall mounting equipment racks easier. Simply put, the XLS is most reliable, versatile, efficient power amp available today. This high-performance line consists of four models each providing enormous power and flexibility thanks to the integrated DriveCore™ Technology, PureBand™ Crossover System and Peakx™ limiters. Generating chest-thumping lows and crystal clear highs, the four models in the series, the XLS1000, XLS1500, XLS2000, and XLS2500, are engineered to meet the demanding audio requirements of your group fitness sound system, reliably and within budget. Every XLS Series amplifier is backed by Crown's unequaled Three-Year, No-Fault, Fully Transferable Warranty that covers everything. With over five decades of experience designing and building rock-solid products, Crown is the world standard in amplifier technology. So check out the Crown XLS Series. They are the definition of performance, flexibility, and value!
- Sensitivity (for full rated power at 4 ohms): 1.4 Vrms
- Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB
- Signal-to-Noise Ratio: 103 dB
- Damping Factor (8 ohm): 10 Hz to 400 Hz >200
- Crosstalk At 1kHz: > 85dB, At 20kHz: >55dB
- Input Impedance (nominal): 20 kΩ balanced, 10 kΩ unbalanced
- Load Impedance: 2 to 8 Ω per channel in Stereo, 4 to 8 Ω in Bridge Mono
- Ventilation: Flow-through ventilation from front to back
- Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipatio
- PureBand™ Crossover System
- Crossover Filter: Linkwitz-Riley 24dB per Octave
- Crossover Frequency Range: 50 HZ - 3 kHz
- Crossover Mode: Crossover (CH1=LPF, CH2=HPF), LowPass (both channels LPF), HighPass (both channels HPF), Bridge (LPF or HPF).
- Peakx™ limiters: Channel independent clip limiter designed to provide maximum output while protecting your loudspeakers
- Input Connectors: XLR (one per channel), 1/4-Inch (one per channel), and RCA (one per channel). 1/4-Inch connectors can be used as loop-thrus to distribute signal to additional amplifiers.
- Output Connectors: Two 4-Pole Speakon® Output Connectors accept 2-pole or 4-pole Speakon® connectors. The top Speakon connector is wired for both channels so it can be used for bridge mono wiring or for stereo wiring of two speakers to a single Speakon connector.
- One pair of back-panel binding posts per channel; acceptsbanana plugs or bare wire.
- Standard 19-inch (48.3-cm) rack mount width
- 3.5-inch (8.9-cm) height.
- 7.7-inch (19.6-cm) depth.
- Net Weight , Shipping Weigh: XLS1500: 8.6 lb (3.9kg), 13.6 lb (6.2 kg)
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- 300 Watts per channel at 8-ohms
- 525 Watts per channel at 4-ohms
- Integrated PureBand™ Crossover System for better performance and control
- Peakx™ Limiters provide maximum output while protecting your speakers
- XLR, 1/4", RCA inputs provide outstanding flexibility
- Efficient forced-air fans prevent excessive thermal buildup
- Electronically balanced XLR inputs; touchproof binding post and Speakon® outputs
- Precision detented level controls, power switch, power LED, and six LEDs which indicate signal, clip and fault for each channel
- Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications
|
|
|
|
|
|
|
|
|
